04-16-2017, 06:49 AM

B.TECH. ELECTRICAL ENGINEERING

SCIENCE BASED OPEN ELECTIVE

EOE-031 / EOE-041 Introduction to Soft Computing (Neural

Networks, Fuzzy Logic and Genetic Algorithm)

EOE-032 / EOE-042 Nano Sciences

EOE-033 / EOE-043 Laser Systems and Applications

EOE-034 / EOE-044 Space Sciences

EOE-035 / EOE-045 Polymer Science & Technology

EOE-036 /EOE-046 Nuclear Science

EOE-037 / EOE-047 Material Science

EOE-038 / EOE-048 Discrete Mathematics

OPEN ELECTIVE-I

EOE -071 Entrepreneurship Development

EOE-072 Quality Management

EOE-073 Operations Research

EOE-074 Introduction to Biotechnology

OPEN ELECTIVE-II

EOE-081 Non Conventional Energy Resources

EOE-082 Nonlinear Dynamic Systems

EOE-083 Product Development

EOE-084 Automation & Robotics

[10]

EME-309 : THERMAL AND HYDRAULIC MACHINES

L T P

3 1 0

UNIT-I

Thermodynamic equilibrium, cyclic process, enthalpy, Zero, first and second laws of thermodynamics,

carnot cycle, concept of entropy, properties of steam, processes involving steam in closed

and open systems, Enthalpy.

Vapour Pressure Cycles:

Rankine cycle, reheat cycle, Regenerative cycle

UNIT-II

Steam Turbine:

Classification, impulse and reaction turbines their velocity diagrams and related calculations, workdone

and efficiencies, re-heat factor, staging, bleeding and governing of turbines.

Gas Turbine:

Classification, Brayton cycle, working principle of gas turbine, gas turbine cycle with intercooling,

reheat and regeneration, stage and polytrophic efficiencies.

UNIT-II

Compressors:

Classification, single and multistage reciprocating compressors, isothermal and volumetric

efficiencies, centrifugal and axial flow compressors, surging, choking and stalling.

I.C. Engines:

Otto, Diesel . and Dual cycles, introduction to 2-stroke and 4-stroke SI and CI engines, indicator

diagram and power measurement.

UNIT-IV

Impact of Jet:

Introduction to hydrodynamic thrust of jet on a fixed and moving surface ( flat and curve), effect of

inclination of jet with the surface.

Hydraulic Turbines:

Classification, heads and efficiencies, construction, working, work done and efficiency of impulse and

reaction turbines.

UNIT-V

Centrifugal Pump::

Classification, construction, working, work-done, efficiencies, cavitation and priming; jet pump

Reciprocating Pump:

Classification,construction, working, work-done, slip and coefficient of discharge.

Text Books:

1. Onkar Singh Applied Thermodynamics New Age International, 2006

2. R.K.Rajput A Text Book of Hydraulic Machines S. Chand & Co.,2008.

Reference Books:

3. P.L.Ballany Thermal Engineering Khanna Publishers, 2003

4. R.K.Bansal A Text Book of Fluid Mechanics and Hydraulic Machines Laxmi Publications,

2006.

[11]

EAS-301/EAS-401: MATHEMATICS II

L T P

3 1 0

Unit I :

Function of Complex variable

Analytic function, C-R equations, Cauchy s integral theorem, Cauchy s integral formula for derivatives of

analytic function, Taylor s and Laurent s series, singularities, Residue theorem, Evaluation of real integrals of

the type and 10

Unit II :

Statistical Techniques - I

Moments, Moment generating functions, Skewness, Kurtosis, Curve fitting, Method of least squares, Fitting of

straight lines, Polynomials, Exponential curves etc., Correlation, Linear, non linear and multiple regression

analysis, Probability theory. 08

Unit II :

Statistical Techniques - II

Binomial, Poisson and Normal distributions, Sampling theory (small and large), Tests of significations: Chisquare

test, t-test, Analysis of variance (one way) , Application to engineering, medicine, agriculture etc.

Time series and forecasting (moving and semi-averages), Statistical quality control methods, Control charts, ,

R, p, np, and c charts. 08

Unit IV : Numerical Techniques I

Zeroes of transcendental and polynomial equation using Bisection method, Regula-falsi method and Newton-

Raphson method, Rate of convergence of above methods.

Interpolation: Finite differences, difference tables, Newton s forward and backward interpolation , Lagrange s

and Newton s divided difference formula for unequal intervals. 08

Unit V :

Numerical Techniques II

Solution of system of linear equations, Gauss- Seidal method, Crout method. Numerical differentiation,

Numerical integration , Trapezoidal , Simpson s one third and three-eight rules, Solution of ordinary

differential (first order, second order and simultaneous) equations by Euler s, Picard s and forth-order Runge-

Kutta mehthods. 08

Test Books :-

1. Peter V. O Neil, Advance Engineering Mathematics Thomson (Cengage) Learning, 2007.

2. Jain, Iyenger & Jain, Numerical Methods for Scientific and Engineering Computation, New Age

International, New Delhi , 2003.

3. J.N. Kapur, Mathematical Statistics, S. Chand & company Ltd.,2000

Reference Books :-

1. R.K. Jain & S.R.K. Iyenger, Advance Engineering Mathematics, Narosa Publication House, 2002.

2. Chandrika Prasad, Advanced Mathematics for Engineers, Prasad Mudralaya, 1996.

3. E. Kreysig, Advanced Engineering Mathematics, John Wiley & Sons, 2005.

4. B.S. Grewal, Higher Engineering Mathematics, Khanna Publishers, 2005.

5. Devi Prasad, An introduction to Numerical Analysis, Narosa Publication house, New Delhi 2006.

6. T. Veerajan & T. Ramchandrandran, Theory & Problems in Numerical Methods, TMH, New Delhi,

2004.

7. S.P.Gupta, Statistical Methods, Sultan and Sons, New Delhi, 2004.

8. Devore, Probability and Statistics, Thomson(Cengage) Learning, 2007.

9. Walpole, Myers, Myers & Ye, Probability and Statistics for Engineers & Scientists, Pearson Education,

2003.

[12]

EE-301: BASIC SYSTEM ANALYSIS

L T P

3 1 0

UNIT I

Introduction to continuous time signals and systems: Basic continuous time signals, unit step,

unit ramp, unit impulse and periodic signals with their mathematical representation and

characteristics. Introduction to various types of systems.

Analogous System: Linear mechanical elements, force-voltage and force-current analogy,

modeling of mechanical and electro-mechanical systems: Analysis of first and second order linear

systems by classical method. (9)

UNIT II

Fourier Transform Analysis : Exponential form and Trigonometric form of Fourier series,

Fourier symmetry, Fourier Integral and Fourier Transform. Transform of common functions and

periodic wave forms: Applications of Fourier Transform to network analysis. (8)

UNIT II

Laplace Transform Analysis : Review of Laplace Transform , Laplace Transform of periodic

functions, Initial and Final Value Theorems, Inverse Laplace Transform , Convolution Theorem,

Superposition Integral , Application of Laplace Transform to analysis of networks, waveform

synthesis and Laplace Transform of complex waveforms. (8)

UNIT IV

State Variable analysis : Introduction, State Space representation of linear systems, Transfer

Function and state Variables , State Transition Matrix, Solution of state equations for

homogeneous and non-homogeneous systems , Applications of State-Variable technique to the

analysis of linear systems (8)

UNIT V

Z-Transform Analysis : Concept of Z-Transform, Z-Transform of common functions, Inverse ZTransform,

Initial and Final Value theorems , Applications to solution of difference equations,

Pulse Transfer Function. (7)

Text Books:

1. David K.Cheng; Analysis of Linear System , Narosa Publishing Co.

2. ME Van-Valkenberg; Network Analysis , Prentice Hall of India

3. C.L.Wadhwa, Network Analysis and Synthesis , New Age International

Publishers,2007.

4. Samarajit Ghosh, Network Theory: Analysis and Synthesis Prentice Hall of India, 2008

Reference Books:

5. Choudhary D.Roy, Network & Systems , Wiley Eastern Ltd.

6. Donald E.Scott, Introduction to circuit Analysis Mc. Graw Hill

7. B.P. Lathi, Linear Systems & Signals Oxford University Press, 2008.

8. I.J. Nagrath, S.N. Saran, R. Ranjan and S.Kumar, Singnals and Systems, Tata Mc. Graw

Hill, 2001.

9. Taan S. Elali & Mohd. A. Karim, Continuous Signals and Systems with MATLAB 2nd Edition, CRC Press.

EE-302: ELECTRICAL MEASUREMENT & MEASURING INSTRUMENTS

L T P

3 1 0

UNIT I:

(1) Philosophy Of Measurement: Methods of Measurement, Measurement System, Classification of

instrument system, Characteristics of instruments & measurement system, Errors in measurement &

its analysis, Standards. (3)

[13]

(2) Analog Measurement of Electrical Quantities : Electrodynamic ,Thermocouple, Electrostatic

& Rectifier type Ammeters & Voltmeters , Electrodynamic Wattmeter, Three Phase Wattmeter,

Power in three phase system , errors & remedies in wattmeter and energy meter. (5)

UNIT II:

Instrument Transformer and their applications in the extension of instrument range, Introduction to

measurement of speed , frequency and power factor. (6)

UNIT II:

Measurement of Parameters: Different methods of measuring low, medium and high resistances,

measurement of inductance & capacitance with the help of AC Bridges, Q Meter. (7)

UNIT IV:

(1) AC Potentiometer: Polar type & Co-ordinate type AC potentiometers , application of AC

Potentiometers in electrical measurement (3)

(2) Magnetic Measurement: Ballistic Galvanometer , flux meter , determination of hysteresis loop,

measurement of iron losses. (4)

UNIT V:

(1) Digital Measurement of Electrical Quantities: Concept of digital measurement, block diagram

Study of digital voltmeter, frequency meter Power Analyzer and Harmonics Analyzer; Electronic

Multimeter.

(2)Cathode Ray Oscilloscope : Basic CRO circuit (Block Diagram),Cathode ray tube (CRT) & its

components , application of CRO in measurement ,Lissajous Pattern.; Dual Trace & Dual Beam

Oscilloscopes. (3)

Text Book:

1. E.W. Golding & F.C. Widdis, Electrical Measurement &Measuring Instrument , A.W.

Wheeler& Co. Pvt. Ltd. India.

2. A.K. Sawhney, Electrical & Electronic Measurement & Instrument , Dhanpat Rai & Sons ,

India .

Reference Books:

3. Forest K. Harries, Electrical Measurement ,Willey Eastern Pvt. Ltd. India .

4. M.B. Stout , Basic Electrical Measurement Prentice hall of India,India.

5. W.D.Cooper, Electronic Instrument & Measurement Technique Prentice Hall International.

6. Rajendra Prashad , Electrical Measurement &Measuring Instrument Khanna Publisher.

7. J.B. Gupta, Electrical Measurements and Measuring Instruments , S.K. Kataria & Sons.

[/b]

LT P

3 1 0

ANALOG ELECTRONICS:

UNIT-I:

Special Diodes-

LED, Varactor diode, Photo diode, Schottky diode, Tunnel diode; their characteristics and

applications.

Transistors as a switch.

UNIT-II

Frequency Response:

Amplifier transfer function, low and high frequency response of common emitter and common

source amplifiers.

Feedback:

General feedback structure; properties of negative feedback; series-series, series-shunt, shuntseries

and shunt-shunt feedback amplifiers.

[14]

UNIT-II:

Basic principle of sinusoidal oscillator, R-C Phase Shift and Wein Bridge oscillators, tuned

oscillators- Collpits and Hartley; Crystal oscillator

DIGITAL ELECTRONICS:

UNIT-IV

Combinational Logic Circuits: Multiplexers/Demultiplexures, Encoders/Decoders.

Sequential Logic Circuits: latches, flip-flops- S-R, T, D, J-K.

Shift Registers: Basic principle, serial and parallel data transfer, shift left/right registers,

universal shift register.

Counters: Mode N Counters, ripple counters, synchronous counters, ring/Johnson counters.

UNIT-V

OP-AMP applications - Astable, Monostable and Bistable multivibrators, Schmitt trigger, IC-

555 Timer, A/D and D/A converters.

Voltage Regulators: Series, shunt and switching regulators, op-amp based configurations.

Memories: Introduction to ROM, RAM; Sequential Memory, Memory organization.

Text Books:

1. A.S. Sedra and K.C. Smith Microelectronics Circuits Oxford University Press ( India)

2. Malvino & Leach, Digital Principles and applications Tata Mc. Graw Hill

3. R.A. Gayakwad Op amps and Linear Integrated Circuits Prentice Hall of India.

4. Balbir Kumar and Shail B.Jain, Electronic Devices and Circuits Prentice Hall of

India,2007

Reference Books:

1. Taub & Schilling Digital Electronics - Tata Mc Graw Hill

2. Anil K. Maini, Digital Electronics: Principles and Integrated circuits Wiley India Ltd,

2008.

3. Millman, J. and Grabel A, Microelectronics Mc Graw Hill

4. Anand Kumar, Switching Theory and Logic Design Prentice Hall of India, 2008.

5. Aloke. K. Dutta, Semiconductor Devices and circuits , Oxford University Press, 2008.

EE-351: NUMERICAL TECHNIQUE LAB

L T P

0 0 2

Note: Minimum seven experiments out of the following list:

MATLAB Based Experiments

1. Solution of linear equations for under damped and over damped cases.

2. Determination of eigen values and eigenvectors of a square matrix.

3. Determination of roots of a polynomial.

4. Determination of polynomial using method of least square curve fitting.

5. Determination of polynomial fit, analyzing residuals, exponential fit and error bounds from the

given data.

6. Solution of differential equations using 4th order Runge-Kutta method.

7. Solution of differential equation using revised Euler method.

8. Solution of difference equations.

9. Determination of time response of an R-L-C circuit.

10. College may add any three experiments in the above list.

Text/Reference Books:

1. Almos Gilat, MATLAB: An Introduction with Applications Wiley India Ltd., 2004.

2. R.P. Singh, Getting Started with MATLAB Oxford University Press.

[15]

EE-352: ELECTRICAL MEASUREMENT LAB

L T P

0 0 3

Note: Minimum of nine experiments from the following:

1. Calibration of ac voltmeter and ac ammeter

2. Measurement of form factor of a rectified sine wave and determine source of error if

r.m.s.value is measured by a multi-meter

3. Measurement of phase difference and frequency of a sinusoidal ac voltage using C.R.O.

4. Measurement of power and power factor of a single phase inductive load and to study effect of

capacitance connected across the load on the power factor

5. Measurement of low resistance by Kelvin s double bridge

6. Measurement of voltage, current and resistance using dc potentiometer

7. Measurement of inductance by Maxwell s bridge

8. Measurement of inductance by Hay s bridge

9. Measurement of inductance by Anderson s bridge

10. Measurement of capacitance by Owen s bridge

11. Measurement of capacitance by De Sauty bridge

12. Measurement of capacitance by Schering bridge

13. Study of Frequency and differential time counter

14. College may add any two experiments in the above list

EEC-359 : ELECTRONICS LAB

L T P

0 0 2

ANALOG ELECTRONICS:

Note: Select at least any five out of the following:

1. To Plot V-I characteristics of junction diode and zener diode.

2. To draw wave shape of the electrical signal at input and output points of the half wave, full

wave and bridge rectifiers.

3. To Plot input / output characteristics for common base transistor.

4. To Plot input /output characteristics of FET and determine FET parameters at a given

operating point.

5. To determine voltage gain, current gain, input impedance and output impedance of

common emitter amplifier.

6. To determine voltage gain, current gain, input impedance and output impedance and

frequency response of R-C coupled common emitter amplifier.

7. To design R-C Phase shift / Wein Bridge oscillator and verify experimentally the frequency

of oscillation.

8. To study transistor as a switch and determine load voltage and load current when the

transistor is ON.

[b]ANALOG IC & DIGITAL ELECTRONICS:

Note: Select at least any five out of the following:

9. To study application of Operational Amplifier as summer integrator and voltage

comporator

[16]

10. To study operation of Op-Amp based astable and monostable multivibrators.

11. To study operation IC 555 based astable and monostable multibrators.

12. To study operation of (a) multiplexer using IC 74150 (b) demultiplexer using IC 74138.

13. To study operation of Adder / Subtractor using 4 bit / 8 bit IC 7483.

14. To study operation of (a) J K Master slave flip flop using IC 7476 (b) Modulo N

counter using programmable counter IC74190.

15. To verify experimentally output of A/D and D/A converters.

16. To study regulation of unregulated power supply using IC 7805/7812 voltage regulator and

measure the load and line regulations

EE 401: ELECTRO-MECHANICAL ENERGY CONVERSION I

L T P

3 1 0

Unit I

Principles of Electro-mechanical Energy Conversion - Introduction, Flow of Energy in

Electromechanical Devices, Energy in magnetic systems(defining energy & Co-energy) , Singly

Excited Systems; determination of mechanical force, mechanical energy, torque equation , Doubly

excited Systems; Energy stored in magnetic field, electromagnetic torque , Generated emf in

machines; torque in machines with cylindrical air gap . (7)

Unit 2

D.C. Machines:- Construction of DC Machines, Armature winding, Emf and torque equation ,

Armature Reaction ,Commutation , Interpoles and Compensating Windings, Performance

Characteristics of D.C. generators. (9)

Unit 3

D.C. Machines (Contd.):- Performance Characteristics of D.C. motors ,Starting of D.C. motors ; 3

point and 4 point starters , Speed control of D.C. motors: Field Control , armature control and Voltage

Control (Ward Lenonard method); Efficiency and Testing of D.C. machines (Hopkinson s and

Swinburn s Test). (8)

Unit 4.

Single Phase Transformer: Phasor diagram, efficiency and voltage regulation, all day efficiency.

Testing of Transformers: O.C. and S.C. tests, Sumpner;s test, polarity test.

Auto Transformer: Single phase and three phase auto transformers, volt-amp, relation, efficiency,

merits & demerits and applications.

Unit 5

Three Phase Transformers: Construction, three phase transformer phasor groups and their

connections, open delta connection, three phase to 2 phase, 6 phase or 12 phase connections, and their

applications, parallel operation and load sharing of single phase and three phase transformers,

excitation phenomenon and harmonics in transformers, three winding transformers.

Text Books:

1 I.J. Nagrath & D.P.Kothari, Electrical Machines , Tata McGraw Hill

2 Husain Ashfaq , Electrical Machines , Dhanpat Rai & Sons

3 A.E. Fitggerald, C.Kingsley Jr and Umans, Electric Machinery 6th Edition

McGraw Hill, International Student Edition.

4 B.R. Gupta & Vandana Singhal, Fundamentals of Electrical Machines, New Age International.

Reference Books:

5 Irving L.Kosow, Electric Machine and Tranformers , Prentice Hall of India.

6 M.G. Say, The Performance and Design of AC machines , Pit man & Sons.

7 Bhag S. Guru and Huseyin R. Hizirogulu, Electric Machinery and Transformers Oxford

University Press, 2001.

[17]

EE- 402:NETWORK ANALYSIS AND SYNTHESIS

L T P

3 1 0

Unit I:

Graph Theory : Graph of a Network, definitions, tree, co tree , link, basic loop and basic cut set,

Incidence matrix, cut set matrix, Tie set matrix Duality, Loop and Nodal methods of analysis. (7)

Unit II:

Network Theorems (Applications to ac networks): Super-position theorem, Thevenin s theorem,

Norton s theorem, maximum power transfer theorem, Reciprocity theorem. Millman s theorem,

compensation theorem, Tellegen s theorem. (8)

Unit II :

Network Functions :

Concept of Complex frequency , Transform Impedances Network functions of one port and two port

networks, concept of poles and zeros, properties of driving point and transfer functions, time response

and stability from pole zero plot. (8)

Unit IV :

Two Port Networks:

Characterization of LTI two port networks ZY, ABCD and h parameters, reciprocity and symmetry.

Inter-relationships between the parameters, inter-connections of two port networks, Ladder and

Lattice networks. T & Representation. (8)

Unit V :

(a) Network Synthesis :

Positive real function; definition and properties; properties of LC, RC and RL driving point functions,

synthesis of LC, RC and RL driving point immittance functions using Foster and Cauer first and

second forms.

(b) Filters:

Image parameters and characteristics impedance, passive and active filter fundamentals, low pass,

highpass, (constant K type) filters, and introduction to active filters. (9)

Text Books:

1 M.E. Van Valkenburg, Network Analysis , Prentice Hall of India

2 A.Chakrabarti, Circuit Theory Dhanpat Rai & Co.

3 C.L Wadhwa, Network Analysis and Synthesis New Age International Publishers, 2007.

4 D.Roy Choudhary, Networks and Systems Wiley Eastern Ltd.

5 Donald E. Scott: An Introduction to Circuit analysis: A System Approach McGraw Hill

Reference Books:

6 M.E. Van Valkenburg, An Introduction to Modern Network Synthesis ,Wiley Eastern Ltd.

7 N.C. Jagan and C. Lakshminarayana, Newwork Analysis B.S. Publications, 2008.

8 K.S. Suresh Kumar, Electric Circuits and Networks Pearson Education, 2009.

9 A Ramakalyan, Linear Circuits: Analysis and Synthesis Oxford University Press, 2005.